Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included

 1 in stock

Performance 2-1 connecting pipe, de-CAT or H pipe. This mid pipe is 2kg lighter than the original pipe and will make a significant improvement to both the exhaust note and performance of your V85 TT when combined with a performance silencer and air filter SIA10433. We also recommend fitting a V-Twin Boost plug-in FUA85001 with this CAT eliminator to enrich the mixture

• Y piece made from AISI304 stainless steel
• Installation with graphite bushings to limit the transmission of vibrations
• Fixing bracket with antivibration silent block
• Straight through design for better performance and deeper sound
• Larger diameter internals for better exhaust gas flow
• This crossover is compatible with original system components
• Reduces engine operating temperature for better fuel consumption and efficiency
• Includes exhaust bushes
• Modern satin finish
• Manufactured on the shores of Lake Como and developed using a rolling road

 1 in stock

Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.

 1 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

The Mistral V-Twin boost is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's. The V85 TT runs particularly lean and will benefit more than most bikes from the installation of a V-Twin Boost.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The V-Twin boost features a unique technology to provide your bike with a controlled fuel enrichment.
Make your bike run as it should have done from the factory!

• Quick and easy installation
• Resistant to atmospheric agents and vibrations
• Optimized by Mistral for your bike
• Best response to the opening of the throttle
• Better torque at low-medium range
• Reduction of the on/off effect
• Correct air/fuel ratio in all conditions with real-time modification

 1 in stock

Black plastic front mudguard extension or Fenda Extenda for lower mudguard MUA00244. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel

Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours

 1 in stock

Also fits Aprilia Caponord (2013-2017)

Rear hugger finished in matte black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets

Similar matte finish to front mudguard MUA00244 .
Supplied with brackets and fasteners. See here for fitting instructions. Fitment of this hugger requires some mechanical skill- if in doubt please entrust this job to a professional

 1 in stock

Pair of sturdy black handguard extensions, manufactured in the UK. These should save your levers from expensive damage in the unfortunate event of your bike falling over or being dropped and offer superior weather protection for year round riding

Compatible with the original factory handlebars. Easily installed. A brace to the mirror perch ensures that these are stable at speed.

 1 in stock

Thick protective tank cover for your workshop. Ideal for preventing expensive damage to your motorcycle tank when working on your bike (avoid brake fluid spills etc...) and also useful for leaving on your bike when not in use to avoid accidental scratches. Special anti-slip material on underside secures cover to your motorcycle tank when in use. Upper side is nylon for ease of cleaning.

 1 in stock

Large dust cover for your bike when parked up in your garage. Prevents dust and dirt settling on your pride and joy. Also useful for hiding your bike from prying eyes when your garage door is open. Also see tank protector SIA00001 for extra protection.

Breathable, tear resistant fabric.

 1 in stock